A 30″ spacing from bunk to bunk might be good if the bunk sits vertical (the 4″ dimension of a 2×4 is vertical). If the 2″ dimension is vertical you may not have enough clearance and the hull could scrap the trailer cross member.
How far apart are the bunks on a jet ski trailer?
Jet Boat Lover
I measured the inside width of the front trailer bunks at the furthest point from the hitch to be 23″. I set the bunks on the lift to be 23″ (inside distance) at the front and 36″ (inside distance) on the rear.
How far apart should bunk boards be?
Your bunks should be spaced identically off of the center line of the trailer. Or, each bunk should be equally spaced from each side of each outside frame on the trailer at the same front to back trailer location. 3.
How wide are jet ski bunks?
Most stands come in multiple bunk widths. The AquaCart AQ-11, for instance, comes in three bunk widths: 20 inches, which fits most sit-down models of PWC, 14 inches, which fits “V”-hulled models of PWC, including most performance models, as well as stand-up models, and 12 inches, which fits most stand-up models.
How long should bunks be?
The general rule of thumb is that you want your bunks to extend completely to the stern (rear) of the boat, or even and inch or two beyond. That way the transom has plenty of support as you drive down the road.
How should a jet ski sit on a trailer?
The jet ski should always sit on the trailer in a centered position as it has to be balanced on the trailer. Also make sure to pull it up completely until the bow reaches the bow stop and attach the safety chain!
What are the dimensions of a jet ski trailer?
A double jet ski trailer is around 170-230 inches long. One of the shortest double jet ski trailers is the PWT2212G from Com-Fab, as this model is just 167 inches long. The longest jet ski double trailers are usually equipped with storage boxes and racks, and can reach 230 inches length.
How long should my boat trailer bunks be?
Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like.
What kind of wood should be used for boat trailer bunks?
For wood, pressure-treated pine is the industry standard for trailer bunks. Popular alternatives are oak, cypress and other hardwoods that add even more durability. Composite boards used for patio decking are other options, but pressure-treated pine is a proven material with economic benefits.
How do you adjust trailer bunks?
you can use your wrench to loosen the bolts that hold the bunks brackets in place on your boat trailer. Start at the most forward point of the bunk, raise the bunk until it touches the bottom of your boat and tighten until the bunk is in place.
Can you haul one jet ski on a double trailer?
Double trailers are designed to safely tow one or two skis. You will be ok, the weight is still between the wheels regardless of one or two skis on it.
How long is a jet ski in feet?
The United States Coast Guard defines a personal watercraft, amongst other criteria, as a jet-drive boat less than 13 feet (4 m) long. There are many larger “jetboats” not classed as PWCs, some more than 40 feet (12 m) long.
How should a boat sit on a bunk trailer?
Set boat on trailer while maintaining no less than 2″ gap between keel and tongue plate cover. The end of the bunks/rollers should be flush with transom and the boweye should reach the winch post. If this is so, the rear pivot should remain in the A-position.
How many feet does a trailer add to a boat?
In general, trailers are typically about two feet longer than the boat itself. Do not use LOA (which can be influenced by extended swim platforms) as an indicator of boat length, as a trailer only supports the hull’s running surface.
How are boat trailers measured?
Measure with a measuring tape along the center line of the trailer, the distance from the front of the hitch to the center of the back rail of the frame of the trailer. Your boat needs to fit within the space afforded by the trailer.